1 sy10e416 sy100e416 micrel, inc. m9999-032206 hbwhelp@micrel.com or (408) 955-1690 description features differential d and q extended 100e v ee range of ?.2v to ?.5v vbb output for single-ended use 600ps max. propagation delay high frequency outputs 2 stages of gain internal 75k ? input pull-down resistors fully compatible with motorola 10e/100e416 available in 28-pin plcc package the sy10/100e416 are 5-bit differential line receiving devices. the 2.0ghz of bandwidth provided by the high frequency outputs make the devices ideal for buffering of very high speed oscillators. a v bb pin is available to ac couple an input signal to the devices. the design incorporates two stages of gain internal to the devices, making them an excellent choice for use in high bandwidth amplifier applications. quint differential line receiver sy10e416 sy100e416 block diagram d 0 d 0 q 0 q 0 d 1 d 0 q 1 q 1 d 2 d 2 q 2 q 2 d 3 d 3 q 3 q 3 d 4 d 4 q 4 q 4 v bb pin function d[0:4], d[0:4] differential data inputs q[0:4], q[0:4] differential data outputs v cco v cc to output pin names rev.: f amendment: /0 issue date: march 2006
2 sy10e416 sy100e416 micrel, inc. m9999-032206 hbwhelp@micrel.com or (408) 955-1690 package/ordering information ordering information (1) package operating package lead part number type range marking finish sy10e416ji j28-1 industrial sy10e416ji sn-pb sy10e416jitr (2) j28-1 industrial sy10e416ji sn-pb SY100E416JI j28-1 industrial SY100E416JI sn-pb SY100E416JItr (2) j28-1 industrial SY100E416JI sn-pb sy10e416jc j28-1 commercial sy10e416jc sn-pb sy10e416jctr (2) j28-1 commercial sy10e416jc sn-pb sy100e416jc j28-1 commercial sy100e416jc sn-pb sy100e416jctr (2) j28-1 commercial sy100e416jc sn-pb sy10e416jy (3) j28-1 industiral sy10e416jy with matte-sn pb-free bar-line indicator sy10e416jytr (2, 3) j28-1 industrial sy10e416jy with matte-sn pb-free bar-line indicator sy100e416jy (3) j28-1 industrial sy100e416jy with matte-sn pb-free bar-line indicator sy100e416jytr (2, 3) j28-1 industrial sy100e416jy with matte-sn pb-free bar-line indicator notes: 1. contact factory for die availability. dice are guaranteed at t a = 25 c, dc electricals only. 2. tape and reel. 3. pb-free package is recommended for new designs. 28-pin plcc (j28-1) 18 17 16 15 14 13 12 567891011 26 27 28 1 2 3 4 top view plcc j28-1 25 24 23 22 21 20 19 d 2 v ee v bb d 0 d 3 d 2 d 0 d 1 v cco q 0 v cco q 1 d 1 q 0 q 3 v cc q 2 v cco q 3 q 2 q 1 d 4 v cco q 4 d 3 v cco d 4 q 4
3 sy10e416 sy100e416 micrel, inc. m9999-032206 hbwhelp@micrel.com or (408) 955-1690 t a = 0 ct a = +25 ct a = +85 c symbol parameter min. typ. max. min. typ. max. min. typ. max. unit condition t pd propagation delay to output ps d (diff) 250 350 500 250 350 500 250 350 500 d (se) 200 350 550 200 350 550 200 350 550 t skew within-device skew 50 50 50 ps 1 t skew duty cycle skew, t plh ? phl 10 10 10 ps 2 v pp (ac) minimum input swing 150 150 150 mv 3 t r rise/fall time 100 200 350 100 200 350 100 200 350 ps t f 20?0% t a = 0 ct a = +25 ct a = +85 c symbol parameter min. typ. max. min. typ. max. min. typ. max. unit condition v bb output reference voltage v 10e ?.38 ?.27 ?.35 ?.25 ?.31 ?.19 100e ?.38 ?.26 ?.38 ?.26 ?.38 ?.26 i ih input high current 150 150 150 a i ee power supply current ma 10e 135 162 135 162 135 162 100e 135 162 135 162 155 186 v pp (dc) input sensitivity 50 50 50 mv 1 v cmr common mode range ?.5 0 ?.5 0 ?.5 0 v 2 dc electrical characteristics v ee = v ee (min.) to v ee (max.); v cc = v cco = gnd notes: 1. differential input voltage required to obtain a full ecl swing on the outputs. 2. v cmr is referenced to the most positive side of the differential input signal. normal operation is obtained when the input signals are within the v cmr range and the input swing is greater than v pp (min.) and <1v. ac electrical characteristics v ee = v ee (min.) to v ee (max.); v cc = v cco = gnd notes: 1. within-device skew is defined as identical transitions on similar paths through a device. 2. duty cycle skew defined only for differential operation when the delays are measured from the cross point of the inputs to th e cross point of the outputs. 3. minimum input swing for which ac parameters are guaranteed.
4 sy10e416 sy100e416 micrel, inc. m9999-032206 hbwhelp@micrel.com or (408) 955-1690 28-pin plcc (j28-1) rev. 03 micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel + 1 (408) 944-0800 fax + 1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is believed to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intend ed for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant inj ury to the user. a purchaser s use or sale of micrel products for use in life support appliances, devices or systems is at purchaser s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2006 micrel, incorporated.
|
